Weather does the rest. The lagoon and bay keep the air damp and the wind funnels through the gap toward Wauna. Hard freezes in December 2022 and January 2024 froze crawlspace lines on waterfront cabins and exposed pump houses. Winter rains raise the water table under the shoreline lots within days. We reach Purdy in about 20 minutes from Port Orchard down Highway 16, the closest Pierce County stop we have, and the trucks go out stocked for the jobs this community generates most.
Why well house & pressure tank service is a little different in Purdy
Well houses around Purdy tend to be small, unheated sheds, and the December 2022 and January 2024 freezes split a lot of them open. We insulate lines, add thermostatic heat tape, set tanks off the slab and will tell you plainly whether your building needs a heater before the next cold snap.
Start with the homes. Older waterfront cabins from the 1940s through the 70s along Burley Lagoon and Henderson Bay, 1980s and 90s homes on the uplands, and newer construction spilling north from Gig Harbor North. The waterfront homes are the ones with galvanized supply lines, cast iron under the floor and septic pump chambers; the newer ones bring PEX and tankless heaters.
Local conditions that affect well house & pressure tank service in Purdy
In Purdy specifically, one issue comes up more than most: Private well pressure tanks waterlogged and pumps short-cycling
Homes in Purdy on a hill above the well house or at the end of a long supply line can have a healthy pump and still poor pressure at the shower. Before anyone talks about a bigger pump we check the switch settings, the tank size and the pipe, and we will suggest a booster after the tank if that is the right answer.
Ask a Purdy homeowner what goes wrong with plumbing here and you will usually hear a version of this: Galvanized supply lines in 1950s and 60s cabins choking flow
A number of Purdy properties are on small shared or community well systems rather than a single private well. We service the shared pressure tank, switch and manifold for those systems and coordinate with the other owners or the system operator when a repair affects everyone.
Signs Purdy homeowners call us for well house & pressure tank service
Worth a call
- Air spits from the faucets before the water runs
- The pump cycles at night with every fixture in the house closed
- Rust streaks, a weeping relief valve or a pinhole on the tank or tank tee
- The gauge in the well house is stuck, fogged or reads nothing
- Lines in the well house froze last winter and the building has no heat
How we handle well house & pressure tank service in Purdy
Expect a Purdy well house & pressure tank service call to go like this: tell corinne what the system is doing, diagnose at the well house, flat price on your phone, replace the cluster, not just the part, run it through its cycles, then winter and maintenance advice. If the plan changes mid-job, we stop and re-quote rather than surprise you on the invoice.
Read the full step-by-step for well house & pressure tank service →
Purdy neighborhoods and areas we serve
Our Purdy work runs from Purdy Spit and the bridge across to Burley-Olalla boundary area, and out around Burley Lagoon and Peninsula High School. Anywhere inside the Pierce County side of our territory is fair game.
Well House & Pressure Tank Service questions from Purdy
My Purdy well house froze. Can you fix the plumbing?
Yes. We repair split lines, replace cracked tanks, tees and switches, and insulate and heat the building so it does not happen again next winter.
What pressure tank do you install in Purdy?
Well-X-Trol or Amtrol, sized to your pump and your home rather than to whatever was there before. The tank comes with a new tee, switch, gauge, relief valve and isolation valve.
Can you add filtration in my Purdy well house?
Yes. Sediment, iron and whole-house filtration go in after the pressure tank, and we size them so flow is not restricted. A recent water test tells us what to install.
Is there a charge to diagnose a well house problem in Purdy?
Diagnosis is part of the flat-rate quote, and you approve the price before any repair. If the fix is a breaker or a quick reset, you will not be charged for a tank you did not need, and if it is the pump, you get a referral rather than a bill.
What pressure should my well be set to?
Most homes run 40/60, meaning the pump starts at 40 psi and stops at 60. Single-story homes sometimes run 30/50. A home with a second floor, a long run or a filtration system usually wants 40/60 or a little higher, and the tank precharge has to match. We set both together.
Purdy homeowners often find us after a larger outfit quoted a replacement for something that only needed a repair. We would rather earn a customer for life than win one big ticket.